FLT3-IN-3 (Synonyms: SAN50900) |
| Catalog No.GC19772 |
FLT3-IN-3 is a potent FLT3 inhibitor with IC50s of 13 and 8 nM for FLT3 WT and FLT3 D835Y, respectively.
Products are for research use only. Not for human use. We do not sell to patients.
Cas No.: 2229050-90-0
Sample solution is provided at 25 µL, 10mM.
;)
_1-7.$$$37316672@70.jpg');)
;)
;)
_273-287.$$$36806353@46.jpg');)
_1-16.$$$37156877@44.jpg');)
;)
;)
;)
_1124-1138.$$$35908550@30.jpg');)
_766-780.$$$37100057@30.jpg');)
_418-432.$$$36893736@30.jpg');)
_240-255.$$$35108512@29.jpg');)
_533-545.$$$36543525@28.jpg');)
_264-276.$$$36600053@22.jpg');)
_2214998.$$$@0.jpg');)
FLT3-IN-3 is a potent FLT3 inhibitor with IC50s of 13 and 8 nM for FLT3 WT and FLT3 D835Y, respectively.
FLT3-IN-3 (Compound 7d) inhibits the proliferation of FLT3-ITD positive MV4-11 and MOLM-13 cell lines very effectively at low nanomolar concentrations (GI50 values 2 and 1 nM, respectively)[1].
FLT3-IN-3 (1 nM, 10nM, 100 nM, 1 μM and 10 μM; 72 hours) inhibits the Ba/F3 FLT3-ITD cells with the GI50 of 0.034±0.015 μM, and inhibits the parental Ba/F3 cells with the GI50 value of 1.136±0.389 μM[1].
Concentrations as low as 1 nM are sufficient to block the autophosphorylation of the FLT3 receptor tyrosine kinase at three different tyrosine residues (589, 591, and 842). Moreover, this inhibition suppresses phosphorylation of several downstream targets of FLT3. Notably, FLT3-IN-3 (0.01, 0.1, 1, 10 and 100 nM; 1 hours) abolishes phosphorylation of STAT5 at Y694, which is a direct substrate of the oncogenic FLT3-ITD variant. The second pathway affected is the MAPK cascade: Two key components of this signaling pathway, ERK1/2 (T202/Y204) and MEK1/2 (S217/221), exhibit reduced phosphorylation upon treatment with FLT3-IN-3. FLT3-IN-3 also interfers with PI3K/AKT pathway which is confirmed by reduced phosphorylation of AKT at S473[1]
A single dose of FLT3-IN-3 (Compound 7d; 10 mg/kg; i.p.) in mice with subcutaneous MV4-11 xenografts causes sustained inhibition of FLT3 and STAT5 phosphorylation over 48 hours[1].
Reference:
[1]. Gucký T, et al. Discovery of N2-(4-Amino-cyclohexyl)-9-cyclopentyl- N6-(4-morpholin-4-ylmethyl-phenyl)- 9H-purine-2,6-diamine as a Potent FLT3 Kinase Inhibitor for Acute Myeloid Leukemia with FLT3 Mutations. J Med Chem. 2018 May 10;61(9):3855-3869.
| Cas No. | 2229050-90-0 | SDF | |
| Synonyms | SAN50900 | ||
| Canonical SMILES | N[C@H](CC1)CC[C@@H]1NC2=NC3=C(N=CN3C4CCCC4)C(NC5=CC=C(CN6CCOCC6)C=C5)=N2 | ||
| Formula | C27H38N8O | M.Wt | 490.64 |
| Solubility | DMSO : 250 mg/mL (509.54 mM) | Storage | Store at -20°C |
| General tips | Please select the appropriate solvent to prepare the stock solution according to the
solubility of the product in different solvents; once the solution is prepared, please store it in
separate packages to avoid product failure caused by repeated freezing and thawing.Storage method
and period of the stock solution: When stored at -80°C, please use it within 6 months; when stored
at -20°C, please use it within 1 month. To increase solubility, heat the tube to 37°C and then oscillate in an ultrasonic bath for some time. |
||
| Shipping Condition | Evaluation sample solution: shipped with blue ice. All other sizes available: with RT, or with Blue Ice upon request. | ||
| Prepare stock solution | |||
|
1 mg | 5 mg | 10 mg |
| 1 mM | 2.0382 mL | 10.1908 mL | 20.3815 mL |
| 5 mM | 0.4076 mL | 2.0382 mL | 4.0763 mL |
| 10 mM | 0.2038 mL | 1.0191 mL | 2.0382 mL |
Step 1: Enter information below (Recommended: An additional animal making an allowance for loss during the experiment)
g
μL
Step 2: Enter the in vivo formulation (This is only the calculator, not formulation. Please contact us first if there is no in vivo formulation at the solubility Section.)
Calculation results:
Working concentration: mg/ml;
Method for preparing DMSO master liquid: mg drug pre-dissolved in μL DMSO ( Master liquid concentration mg/mL, Please contact us first if the concentration exceeds the DMSO solubility of the batch of drug. )
Method for preparing in vivo formulation: Take μL DMSO master liquid, next addμL PEG300, mix and clarify, next addμL Tween 80, mix and clarify, next add μL ddH2O, mix and clarify.
Method for preparing in vivo formulation: Take μL DMSO master liquid, next add μL Corn oil, mix and clarify.
Note: 1. Please make sure the liquid is clear before adding the next solvent.
2. Be sure to add the solvent(s) in order. You must ensure that the solution obtained, in the previous addition, is a clear solution before proceeding to add the next solvent. Physical methods such as vortex, ultrasound or hot water bath can be used to aid dissolving.
3. All of the above co-solvents are available for purchase on the GlpBio website.
Quality Control & SDS
- View current batch:
- Purity: >99.50%
- COA (Certificate Of Analysis)
- SDS (Safety Data Sheet)
- Datasheet
Average Rating: 5 (Based on Reviews and 20 reference(s) in Google Scholar.)
GLPBIO products are for RESEARCH USE ONLY. Please make sure your review or question is research based.
Required fields are marked with *