Oxazolone |
|
رقم الكتالوجGC26407
|
Oxazolone is a haptenizing agent that induces acute or chronic inflammation of the large intestine and is used to construct models of colitis.
Products are for research use only. Not for human use. We do not sell to patients.
Cas No.: 15646-46-5
Sample solution is provided at 25 µL, 10mM.
Oxazolone is a haptenizing agent that induces acute or chronic inflammation of the large intestine and is used to construct models of colitis. Oxazolone can cause Th1/Th2-dependent colitis with weight loss and diarrhea. Oxazolone-induced inflammation can be mitigated by neutralizing anti-IL-4 or anti-TNF-α antibodies or decoy IL-13R2-α-FC proteins.
Colitis induction
1.Prepare procedure
Preparation of sensitization solution (I):
Mix acetone and olive oil in a 4:1 v/v ratio by vortexing. Dissolve a 60 mg oxazolone in 2 mL of this solution to obtain a 3 % (w/v) oxazolone sensitization solution. Mix the solution by carefully vortexing.
Preparation of challenge solution (II):
Dissolve 20 mg Oxazolone in 2 mL of 50 % ethanol to obtain a 1 % (w/v) solution. Mix the solution by careful vortexing. The oxazolone powder should be completely dissolved before use.
2. Experimental procedure
Sensitization pretreatment:
The electric scissors scraped an area of about 2 cmx2 cm on the skin of the mice's backs. Be careful to avoid open wounds.
Apply 150 μL of sensitizing solution (working solution 1) to the exposed skin of mice. Be careful to use an Oxazolone-free sensitizer as a control. Induction treatment:
Anesthetized mice: intraperitoneally injected ketamine/thiazide solution (80 μL/10 g), or inhaled with isoflurane anesthesia system.
The catheter was inserted into the colon of the mice (about 3-4 cm deep at the proximal end of the anus). The other end of the catheter is connected to a 1 mL syringe.
About 100 μL of oxazolone stimulation solution is injected into the colonic cavity through a catheter for 10 to 30 seconds. After dosing, hold the mouse in a vertical position (head down) for 60 seconds.
GLPBIO has not independently confirmed the accuracy of these methods. They are for reference only.
| Cas No. | 15646-46-5 | SDF | |
| Canonical SMILES | O=C(OC(C1=CC=CC=C1)=N/2)C2=C/OCC | ||
| Formula | C12H11NO3 | M.Wt | 217.22 |
| الذوبان | DMSO : 100 mg/mL (460.36 mM) | Storage | -20°C |
| General tips | Please select the appropriate solvent to prepare the stock solution according to the
solubility of the product in different solvents; once the solution is prepared, please store it in
separate packages to avoid product failure caused by repeated freezing and thawing.Storage method
and period of the stock solution: When stored at -80°C, please use it within 6 months; when stored
at -20°C, please use it within 1 month. To increase solubility, heat the tube to 37°C and then oscillate in an ultrasonic bath for some time. |
||
| Shipping Condition | Evaluation sample solution: shipped with blue ice. All other sizes available: with RT, or with Blue Ice upon request. | ||
| Prepare stock solution | |||
|
1 mg | 5 mg | 10 mg |
| 1 mM | 4.6036 mL | 23.0181 mL | 46.0363 mL |
| 5 mM | 920.7 μL | 4.6036 mL | 9.2073 mL |
| 10 mM | 460.4 μL | 2.3018 mL | 4.6036 mL |
Step 1: Enter information below (Recommended: An additional animal making an allowance for loss during the experiment)
Step 2: Enter the in vivo formulation (This is only the calculator, not formulation. Please contact us first if there is no in vivo formulation at the solubility Section.)
Calculation results:
Working concentration: mg/ml;
Method for preparing DMSO master liquid: mg drug pre-dissolved in μL DMSO ( Master liquid concentration mg/mL, Please contact us first if the concentration exceeds the DMSO solubility of the batch of drug. )
Method for preparing in vivo formulation: Take μL DMSO master liquid, next addμL PEG300, mix and clarify, next addμL Tween 80, mix and clarify, next add μL saline, mix and clarify.
Method for preparing in vivo formulation: Take μL DMSO master liquid, next add μL Corn oil, mix and clarify.
Note: 1. Please make sure the liquid is clear before adding the next solvent.
2. Be sure to add the solvent(s) in order. You must ensure that the solution obtained, in the previous addition, is a clear solution before proceeding to add the next solvent. Physical methods such as vortex, ultrasound or hot water bath can be used to aid dissolving.
3. All of the above co-solvents are available for purchase on the GlpBio website.
Quality Control & SDS
- View current batch:
- Purity: >97.00% Appearance: A solid
- COA (Certificate of Analysis)
- SDS (Safety Data Sheet)
- Datasheet
Average Rating: 5 (Based on Reviews and 30 reference(s) in Google Scholar.)















